Dental X-Rays

Are Dental X-Rays Safe?

Sep 7 • 17 minute read

Are dental x-rays safe?

Some people do not want diagnostic x-rays because they have heard that the radiation is dangerous.  In fact, they pose very little danger.  There are currently two methods of measuring exposure to radiation.  

The first and oldest unit of measure is called a rem.  A rem is a large unit, so exposure to medical radiation is generally measured in millirems (mrem).  (It takes a thousand millirems to make a rem.)  Dental x-rays on the slowest speed film deliver about 4 mrem.  (Most offices now use faster films which reduce radiation by a factor of 2-4, the average dose across the board being about 2 mrem per intraoral film.)  Thus, using the slowest speed film, a full mouth series of dental x rays (18 intraoral films) delivers about 72 mrem.  Apanorex film delivers about 8 mrem.  By comparison, according to the National council on radiation protection and measurements, the average person in the US is exposed to about 360 mrem per year just from background sources.  By this measure, it would take approximately 5 full series of dental radiographs on the slowest speed film to equal the background radiation that the average citizen is exposed to on a yearly basis.  Note that we take a new full series every three to five years on average.  Most offices use faster film reducing the dose of radiation per film by about half.  Offices using digital radiography reduce the radiation by even more.

The Washington State Department of Health has set the maximum safe occupational whole body radiation exposure to 5000 mrem (5 rem)per year.  The same limit holds true for other states as well (ex. New york -- see section 16.6).  Finally, 5000 mrem is the federal total effective, whole body, yearly occupational dose limit.  By this reckoning, it would take about 70 full mouth series of dental x-rays (18 films per survey) over the course of a year to equal one years maximum safe occupational radiation level.  It would take 625 panorex films or 1250 individual intraoral x-rays to get to this limit.  The 5000 mrem yearly limit applies to persons who are routinely exposed to ionizing radiation in the course of their jobs.  This is not to suggest that a member of the general public should routinely expect to be exposed to 5000 mrem per year of diagnostic x-rays, but it is an indication that the benefits of routine yearly diagnostic x-rays far, far outweigh the dangers posed by the radiation. 

The average person in the US is exposed to about 360 mrem per year just from background sources, but the actual amount of background radiation received by any given person varies quite a bit depending upon that individual's lifestyle choices.  Background radiation comes from outer space, the earth, natural materials (including natural foods), and even other people.   For example, flying cross country exposes a person to about 3-5 mrem over and above the normal radiation he receives from outer space while simply walking outdoors for the same length of time.   Cooking with natural gas exposes us to about an additional 10 mrem per year because of the naturally occurring radon gas the cooking gas contains.  Living in a brick building adds an additional 10 mrem per year over and above the radiation you would receive from living in a wooden structure.  Simply sleeping next to another person exposes each bed partner to an extra 2 mrem per year.

The second, newer measure of radiation is the millisievert (mSV) which is a unit of measure that allows for a more meaningful comparison between radiation sources that expose the entire body (such as natural background radiation) and those that only expose a portion of the body (such as dental and medical radiographs).

Dental x-rays are aimed in a tight beam at a small spot on the face.  The only structures that receive the full dose of x-radiation are the tissues in the direct line of fire.  The rest of the body receives only the radiation that is scattered off of the structures in the line of fire.  (Much less radiation scatters from an object in an x-ray beam than from an object in a beam of ordinary light due to the difference in the nature of the respective radiation sources.  Click here for a better understanding of scatter radiation.)  Furthermore, the tissues at which dental x-rays are aimed are much less prone to injury from x-radiation than are tissues in other parts of the body, such as the intestinal lining or reproductive organs and other constantly reproducing tissues.  The newest unit of measurement, the milisievert was designed to take this factor into account. 

The table below is lifted from the website of the American Dental Association and is quite helpful in comparing the amount of radiation received from dental x-rays to other medical and natural sources.  As you can see, by this more realistic measure, it would take 20 full series of x rays to equal the amount of radiation the average citizen picks up from background sources each year:  Note also that radiation to the gastrointestinal (GI) tract is MUCH more damaging than radiation to the chest.  This is due to the increased vulnerability of the lining of the intestine because the cells there are constantly reproducing and being replaced while the cells in the lungs are not. 

Dental radiographs exposure:

       Bitewings (4 films)

       Full-mouth series (about 19 films)

       Panorex (panoramic jaw film)

 

(mSV)

0.038

0.150

0.019

Medical radiographs exposure:
Lower GI series

Upper GI series

Chest

 

4.060

2.440

0.080
Average radiation per person from outer space In Denver, CO (per year)0.510
Average radiation per person in the U.S. from Natural sources (per year)3.000

What about danger to the x-ray technician? (scatter radiation)

The x-radiation figures mentioned above pertain to the patient who is in the direct line of fire from the x-ray tube.  The radiation received by the person taking the x-ray comes exclusively from scatter, which is most easily understood by thinking about a flashlight aimed at a wall in a completely darkened room.  The spot on the wall where the flashlight is aimed is the brightest because it is in the direct line of fire, however, the rest of the room is also dimly illuminated by the light that scatters off the wall.  This scatter is what concerns us since nothing but the patient's face and jaws is directly in the line of fire of the beam.  The flashlight analogy is inexact since x-ray beams are better collimated (they form a tighter beam), and much less x-radiation is scattered from the target than light from the wall because of the nature of the x-radiation itself.  But the analogy still helps you to understand the concept of scatter versus direct illumination.  Furthermore, the strength of the radiation (or light) hitting any unit area falls off geometrically depending on the distance from the source of scatter.  Think of  the flashlight analogy again.  In a very large, dark room the area of the wall two feet from the bright spot is much brighter than an area 20 feet away.  The "brightness" of the scatter illumination falls off as the square of the distance.  A person standing 6 feet away from the target receives one ninth (1/9) as much scatter radiation as a person standing two feet away from the target (6 feet is 3 times further away than 2 feet, and 3 squared is 9).  A person standing 10 feet away (5 times further away) from the target receives one twenty-fifth (1/25).

Digital X-rays

In digital radiography, a sensor replaces the film normally used for traditional radiographs. The sensor plugs into the USB port on an ordinary computer.  The most common type of Intraoral sensors are solid-state electronic devices called “charged-coupled devices” (CCD).  A CCD is composed of millions of light sensitive silicon cells arranged in a rectangular array on the face of the sensor.   Each cell on the face of the sensor will eventually result in one pixel (picture element) in the final image.  

The x-ray photons falling upon each cell create an analog (continuous) electrical voltage.  The level of the voltage produced depends on the number of photons reaching the cell, and this in turn depends on the density of the structures (teeth and bone) between the x-ray source and the CCD.  The voltage level for each pixel is converted to digital data (numbers between 0 and 255) by a relatively simple device called an "analog to digital converter". Each value is interpreted by the computer as a shade of gray.  Zero corresponds to pure white, and 255 corresponds to pure black with intermediate values corresponding to varying shades of gray.  In this way, the image is converted to millions of tiny digital picture elements (pixels) which are reassembled by the computer into a coherent image. 

CCD's used in dental imaging are essentially the same as the CCD's used in digital cameras.  In your home camera, the CCD contains color filter arrays for each pixel so the image can be reassembled in color.  Since dental radiographs are monochrome (shades of gray), the dental CCD does not contain these filters

While digital radiography is a newer technology than the film it replaces, it must be stressed that the image obtained on a digital x-ray is not necessarily any better than one taken using standard x-ray film.  Most brands of digital x-ray sensor are sold on the basis of how close they can come to the image produced using film.  Digital technology does require substantially less radiation than the older D-speed film (only about a quarter as much), but only slightly lower exposures than the newest F-speed films that are used in many dental offices today. 

The largest benefit of digital x-rays is the ability to computer-enhance the images, making them larger, clearer, or higher contrast at will.  This can be helpful, particularly for dentists with less experience in reading traditional film, but it is rarely essential in making a correct diagnosis.  Larger, sharper images are helpful in patient education and in helping patients to accept a treatment plan.  There is no darkroom developing of the images, and the sensor can be moved about in the mouth more quickly than films, which must be exchanged for new ones for each shot.  Thus digital radiography cuts down on the time it takes to expose and process a series of intraoral films.  For these reasons, digital radiography is gaining increasing acceptance in dental offices throughout the US and Europe.

The major dental series

There are three major types of dental x-ray surveys: the initial full mouth series, the yearly bite wing series, and the Panoramic x-ray film.  

The Full Mouth Series (FMX)

This is an example of the full mouth series we take in our office.  It consists of 4 bite wing films which are taken at an angle specifically to look for decay, and 14 periapical films  which are taken from other angles to show the tips of the roots and the supporting bone.  Not all full series look exactly like this one, but they all use some combination of bite wing and periapical x-rays to show a complete survey of the teeth and bones.  We take a full mouth series on everyone over the age of 25 at the initial oral examination, and retake it again every 3 to 5 years. 

Notice that each tooth is seen in multiple films.  This redundancy is important because it gives us lots of information we would not otherwise have.  Each x-ray is shot from at least a slightly different angle and the difference in angulation can reveal many different aspects of the tooth in question.  X-rays are not ordinary 2 dimensional pictures.  They are actually 3 dimensional shadows.  As you knowshadows may be longer or shorter than the object which casts them depending on the angle of the light source and the screen upon which they are projected.  They may also be distorted in other ways as well.  The shadow of your hand may show all 5 fingers spread out if you hold it palm forward facing the light source with the screen directly behind the back of the hand.  On the other hand, the fingers will not be visible at all if the hand is turned so that the thumb is facing the light source and the little finger is facing the screen.  This happens with x-rays also, except that the objects which cast the shadow appear translucent on the film, and it is actually possible to see several objects superimposed over each other.  This is what gives x-rays their 3 dimensional quality, and this is why it is very helpful to have several views, taken from different angles, of any given tooth.    

The bitewing series

A bitewing series consists of either 2 or 4 films taken of the back teeth (although some offices take them on front teeth as well), with the patient biting down so the films contain images of both the top and bottom teeth.  A bitewing series is the minimum set of x-rays that most offices take to document the internal structure of the teeth and gums.  In our office, we take 2 on children under the age of 12, and 4 on everyone older, supplemented by the other periapical films associated with a full series of x rays if the patient is over the age of 25.

The Panoramic Film (Panorex)

As you can see from the image above, the Panorex is a large, single x-ray film that shows the entire bony structure of the teeth and face.   It takes a much wider area than any intra oral film showing structures outside of their range including the sinuses, and the Temperomandibular Joints.  It shows many pathological structures such as bony tumors and cysts, as well as the position of the wisdom teeth. They are quick and easy to take, and cost a little more than a full series of intraoral films.   In addition to medical and dental uses, panoramic films are especially good for forensic (legal) purposes in the identification of otherwise unrecognizable bodies after plane crashes or other mishaps.

Panoramic films differ from the others in that they are entirely extraoral, which means that the film remains outside of the mouth while the machine shoots the beam through other structures from the outside.  It fits into a broad category of medical x-rays called tomographs.  A tomograph is a computer assisted  method of focusing x-rays on a particular slice of tissue and showing that slice on the film as if there were no other structures outside of that slice.   It has a number of real advantages over the intraoral variety of film discussed above.  Since it is entirely extraoral, it works quite well for gaggers who could not otherwise tolerate the placement of films inside their mouths.  The patient stands in front of the machine (pictured on the right), and the x-ray tube swivels around behind his head.  Another advantage of the panoramic film is that it takes very little radiation to expose it.  The amount of radiation needed to expose a panoramic x-ray film is about the same as the radiation needed to expose two intraoral films (periapical or bitewing).  The reason for this is that the film cassette contains an intensifying screen which fluoresces upon exposure to x-rays and exposes the film with visible light as well as x-rays.  

The film on the right is a panoramic view of a child under the age of 12. You can see the adult teeth that are forming underneath the baby teeth.  You can also see the adult second molars which are the 4 half formed teeth toward the outside of the film.  The fact that the second molars are not yet erupted is the reason a dentist or anthropologist can tell that this child is under the age of 12.  For a better understanding of this film click here.

These films have one major disadvantage.   The panoramic film is a lower resolution picture than the intraoral films.  This means that the individual structures which appear on them (such as the teeth and bone) are somewhat fuzzy, and structures like caries (tooth decay) and bony trabeculation (the spongelike bone inside the marrow spaces) are imaged without the fine detail seen on intraoral films.  They are not considered sufficient for the diagnosis of decay, and must be accompanied by a set of bitewing x-rays if they are to be used as an aid for full diagnostic purposes.  The combination of a set of bitewings and a panoramic film is particularly useful for those patients who are to be referred for orthodontic consult, and for extraction of wisdom teeth.  We use the bitewing/panorex combination frequently instead of a full series of intraoral films on patients between the ages of 13 and 30.

The difference between bitewing and periapical films

In a bitewing film, all three elements, the teeth, the film, and the x-ray beam are optimized to give the most undistorted shadows possible.  (The film and teeth are parallel, and the beam is aimed directly at both; at a 90 degree angle.) Thus bitewing films afford the most accurate representation of the true shape of the teeth and associated structures such as decay, fillings, shape of nerves and bone levels.  (To see how the big cavity in the lower tooth was filled, click here.)  

A periapical film like the one on the right is shot from an angle in which the three elements are not necessarily aligned parallel.  Some distortion is introduced on purpose to be sure that the shadow of the entire tooth or teeth in question falls on the film.  This is done because in many instances, the space available in the mouth, or the curvature of the roof of the mouth will not permit parallel placement of the film. This patient had an abscess and was in pain when the film was shot. (To see how this situation is treated, click here.)  

 

Recent Articles

Should You Get Veneers, Bonding, or Crowns?

When it comes to enhancing your smile, modern dentistry offers a range of options to address imperfe ...

5 Tips for Seniors to Protect Their Oral Health

As you age, maintaining good oral health becomes increasingly important. Poor oral hygiene can lead ...

Uncommon Warning Signs You May Have TMD

Temporomandibular joint disorder (TMD) affects millions worldwide, yet it often remains undiagnosed ...

Toledo Dental Arts
Dr. Shabbir Hashim
Creating Beautiful Smiles

2024

Site Map

Our Office

3349 Executive ParkwayToledo, OH 43606Get Directions(419) 537-5000

2024

Site Map

Toledo Dental Arts

3349 Executive Pkwy, Toledo, OH 43606

Phone:(419) 537-5000